Free

Hot-and-Fast Smoked Beef Jerky

Published by Shannon Grendahl

The quick answer

Smoker Temp
180°F
Wood
Mesquite
Est. Cook Time
4 hr
Jump to RecipePlan Cook Schedule

Eye-of-round sliced thin, 24hr marinade, 4hr at 180°F.

Hot-and-Fast Smoked Beef Jerky
180°F4hServes 8Mesquite
Sign in to save
Tested by the Smoke Brothers Guild Test Kitchen. Calibrated-probe temperatures, USDA safe minimums and rest times checked. See our testing standards →

Cook Mode

One step at a time, big text, timers, and your screen stays awake. 0/8 steps done.

Ingredients

Tap to tick off · 0/16 gathered

8servings

Method

    Prep
  1. 30 min

    Partially freeze the eye of round roast for 1-2 hours to make slicing easier. Using a sharp knife or meat slicer, cut the beef against the grain into uniform 1/8 to 1/4 inch thick strips. Trim any visible fat, as fat can become rancid during the jerky making process.

    Why it matters

    Consistent thickness ensures even drying, which is crucial for jerky texture and food safety. Removing fat prevents spoilage.

    Common mistake

    Slicing with the grain results in tougher, stringier jerky. Leaving fat on can lead to off-flavors and reduced shelf life.

  2. Cure / Brine
  3. 24h

    Whisk the listed marinade ingredients until the sugar dissolves. Coat the beef, cover, and refrigerate 24 hours, turning occasionally.

    Why it matters

    The marinade infuses the meat with flavor and helps tenderize it. The long marination time allows the flavors to penetrate deeply. Cure #1 is a critical safety component for curing meats.

    Common mistake

    Not fully submerging the meat in the marinade, leading to uneven flavor distribution.

  4. Pellicle / Dry
  5. 4h

    After marinating, remove the beef strips from the marinade and pat them thoroughly dry with paper towels. Arrange the strips in a single layer on wire racks, making sure they don't touch. Place the racks back in the refrigerator, uncovered, for 2-4 hours, or until the surface of the meat feels tacky.

    Why it matters

    Forming a pellicle (a sticky, dry surface) helps smoke adhere better to the meat and prevents a 'case hardening' effect, allowing the jerky to dry more evenly.

    Common mistake

    Skipping the pellicle step, leading to less smoky flavor and unevenly dried jerky.

  6. Smoker Setup
  7. 180°F20 min

    Preheat your pellet grill or smoker to a consistent 180°F (82°C). Load the smoker with mesquite wood pellets or chips according to your manufacturer's instructions. A water pan is optional but can help maintain humidity, which is less critical for jerky but won't hurt.

    Why it matters

    Maintaining a low, consistent temperature is key for slow dehydration without cooking the meat. Mesquite wood provides a strong, traditional smoky flavor that pairs well with beef jerky.

    Common mistake

    Fluctuating temperatures can lead to uneven drying. Too high a temperature will cook the jerky instead of dehydrating it, resulting in a brittle texture.

  8. Smoke
  9. 180°F4h

    Smoke the racks at 180°F for about 4 hours, rotating halfway through if needed, until dry and pliable rather than brittle. Verify an internal temperature of at least 160°F.

    Why it matters

    Slow, low smoking dehydrates the meat while infusing it with deep smoky flavor. The target internal temperature ensures pathogens are killed while the low ambient temperature preserves protein structure.

    Common mistake

    Opening the smoker too frequently extends cook time and reduces temperature consistency. Over-drying can lead to brittle, unchewable jerky, while under-drying risks spoilage.

  10. 10 min

    To check for doneness, remove a piece of jerky from the smoker and let it cool for a few minutes. It should be firm but still pliable. When bent, it should crack slightly but not break cleanly in half. You should not see any moisture in the center when torn.

    Why it matters

    Properly dried jerky has the right texture and ensures shelf stability. This final check prevents under-drying (which can lead to spoilage) or over-drying (which makes it hard to eat).

    Common mistake

    Judging doneness while the jerky is hot, as it will feel softer and more pliable when warm, making it seem less done than it actually is.

  11. Rest
  12. 1h

    Once the jerky reaches the desired texture, remove it from the smoker. Let it cool completely on a wire rack at room temperature for at least 1 hour. During this time, carryover drying will occur and the texture will firm up slightly.

    Why it matters

    Cooling allows the jerky to fully set its texture and release any residual moisture, preventing condensation and potential mold growth when stored.

    Common mistake

    Packaging jerky while still warm, which can trap moisture and lead to spoilage.

  13. Serve
  14. Package completely cooled jerky airtight. Refrigerate for up to 1 month or freeze for several months.

    Why it matters

    Proper storage ensures the longevity and safety of your homemade jerky, protecting it from moisture and contaminants.

    Common mistake

    Improper storage, such as in a non-airtight container, which dramatically reduces shelf life.

Sauce It

Smoking this for the weekend? Send this recipe to your crew.

Free 12-Page Guide

The Pitmaster Field Manual

Five core habits, meat and wood reference charts, rub formulas, and a printable cook log. Download the free manual and join the Guild email list for new recipes and techniques.

Cooks & Reviews

Guild members can rate this recipe, log their cooks and share photos.

Sign in to continue

Member reviews

No reviews yet — be the first to rate this cook.

Ask the Pitmaster about this recipe

Substitutions, scaling, technique, troubleshooting — get answers grounded in this cook.

Certified Pitmaster Members

Sign in to try the AI Pitmaster on Hot-and-Fast Smoked Beef Jerky. New members get 3 free questions.

Sign in to try

Comments(0)

Sign in to join the discussion.

Loading comments…